Greg B
  • Male
  • New Albany, OH
  • United States
Share
  • Blog Posts
  • Discussions (15)
  • Events
  • Photos
  • Photo Albums
  • Videos

Greg B's Discussions

Type 1 linear drive installation

Started this discussion. Last reply by DoG - RaymarineUK Jul 1, 2013. 1 Reply

Greetings,I am installing a type 1 linear drive on a bristol 35.5. There is not enough room in the stern area to give me a 90 degree angle with the tiller arm. The installation guide calls for 90…Continue

Tags: installation, drive, Linear

Can the P70R be used on a sailboat?

Started this discussion. Last reply by Sophocles Hadjiosif Jul 23, 2017. 4 Replies

Hi,I previously enjoyed having the knob feature on a ST8002 and I would've like to know if I can use a P70R with a x-10 corepack and type 1 mechanical linear drive on my 36 foot 15,000 pound…Continue

Which autopilot control do I need?

Started this discussion. Last reply by Underway - Raymarine, US Oct 10, 2012. 1 Reply

I am upgrading a from a wheel pilot to below deck. I have ST60+ instruments and a A57d chart plotter all networked with a seatalkng backbone. I am putting in a type one linear drive with spx-10…Continue

Tiller arm for type 1 linear drive

Started this discussion. Last reply by Underway - Raymarine, US Oct 8, 2012. 3 Replies

I am installing a type 1 linear drive on a 36 foot sailboat. It currently has a max 8 inch radius bronze tiller arm and the type 1 manual calls for a 10 inch radius tiller arm. Is the 10 inch radius…Continue

Gifts Received

Gift

Greg B has not received any gifts yet

Give a Gift

 

Greg B's Page

Comment Wall

You need to be a member of Raymarine Technical Forum to add comments!

  • No comments yet!
 
 
 

Events

Videos

  • Add Videos
  • View All

Photos

  • Add Photos
  • View All

Latest Activity

Donald Evans replied to Bruce Bayne's discussion Wiring a RayStar 125 to NMEA 0183
"Regarding the NMEA side of an RS125, as it can transmit NMEA data when correctly wired, does this also mean you can wire a standard NMEA GPS receiver to the same point?"
Oct 13
Mark Van Thillo replied to Tim Sheesley's discussion RD418HD parts needed parts diagram?
"Hello, I need to replace the insides of my radar RD418HD and don't need to replace the cover. is their a part number for this? Thank you for your help. Mark"
Oct 9
Jim Pra liked Jon Fitch's discussion Waypoint/route upload to new e series MFD
Oct 4
Joseph J. Job liked Joseph J. Job's profile
Oct 1
Donald Evans replied to Scott A Crego's discussion NMEA0183 (R08004) for my A65
"llllll"
Sep 23
Donald Evans replied to Scott A Crego's discussion NMEA0183 (R08004) for my A65
"Replacement NMEA cables are to be found here: http://www.gps-galore.co.uk/?product_cat=nmea-0183-cable What happened? did someone scrub the link off? There are so many people out there that can't afford to buy new plotters. Please leave it on…"
Sep 23
Donald Evans replied to Scott A Crego's discussion NMEA0183 (R08004) for my A65
Sep 23
James Riley updated their profile
Sep 16
Stephen Gwyn replied to John M Busciglio's discussion ST1000+ ST2000+ Autopilot PARTS needed
"I had the same problem with the ram tube spinning. I opened up the case to find circular bits of plastic at the bottom of the case. I made a bushing to fit between 4. the lead screw drive pulley and 7 the gear box support plate out some food…"
Sep 14
walt hoover replied to walt hoover's discussion autopilots
"I'm now installing the autopilot type 2 pump. When connecting into the steering system can I just tee into the three hydraulic lines or is there a different circut setup. My instruction sheet has me a bit stumped because it shows the pump…"
Sep 10
David Lane updated their profile
Aug 29
dave abrams replied to Erik Hillenmeyer's discussion NMEA GPS to DSC VHF connection
"My set up is all raymarine, S6002 autopilot and an A70 display.  how can I connect my dsc vhf to pick up the gps signal?  hopefully I can do this on the pedistile and not have to run wires back to th computer.  plas keep it simple if…"
Aug 18
Gregory S******* updated their profile
Aug 10
Folkmeister replied to Mikael H's discussion Show vessels name from AIS
"Reactivating this old thread -   My prior boat had an e7 and AIS650 which worked great, vessel names were displayed with target info.  My new boat has older e80 and e120 plotters.  We have just installed AIS, but the vast majority of…"
Aug 10
Carol Shores updated their profile
Aug 8
Jorge Chubretovich updated their profile
Aug 3

© 2018   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service