Wind transducer data to Corepak 150 autopilot computer with Seatalk to Seatalk ng converter in network

When multiple Seatalk instruments are connected to i50s by a Seatalk to Seatalk ng converter, a Seatalk autopilot will usually be connected directly to the multifunction display. The autopilot cannot be connected to any device on the converter's Seatalk spur. 

Questions:

1. If there is no MFD, how do I get wind tranducer data to the Corepak 150/ST6001 autopilot system.

2. In this case, how should cables be connected?

3. Why is it unadvisable to connect the autopilot into the Seatalk spur?

Views: 106

Reply to This

Replies to This Discussion

1. What is the Wind instrument?  Is it a Seatalk device? The i50 instrument displays can work via Seatalk using the Seatalk to Seatalk NG adapter cable that comes with the i50 instrument display.

2. Need more specific information about the components in the system.

3. A ST6001, Type 150 CC, can not be connected to a Seatalk Spur because those Seatalk devices do not have a Seatalk NG interface.

1. The Wind transducer is connected to an ST50+ which is a Seatalk device.

2. Components are a Type 150 CC computer cabled to an ST6001 controller which is not yet cabled to 4 ST50+s which are cabled to a Seatalk to Seatalk ng converter which is cabled to 2 i50s as repeaters. 12V from the distribution panel is supplied to the Seatalk to Seatalk ng converter.

3. The ST6001/150 CC will talk to the ST50+s since all are Seatalk (as opposed to Seatalk ng). 

According to the operators manual for the converter, "the autopilot cannot be connected to any device on the converter's Seatalk spur".

Questions:

A. Could it be that the manual should read: The autopilot cannot be connected to any device on the converter's Seatalk NG spur (but can be connected to devices on a Seatalk spur)?

B. A concern I have is supplying 12 volts to the converter and additional voltage through the red Seatalk wire from the 150 CC. Will this damage the equipment? 

C. If two 12 V inputs are a problem, then I could disconnect just the red wire from the CC 150 and only connect the yellow data wire and unshielded negative/rf screen wire. In other words voltage would be supplied only to the converter which would power all instruments and the autopilot controller. Is this recommended?

A.  The manual has yet to be amended, since the original version of software.  Autopilot data can now be connected with the current revision of software V1.21.

Voltage should be coming from the converter, and the connection you have described in C option is the recommended way to provide power to this system.

thank you Mr. Underway. JD

Anytime.  Contact us if you have any further questions.  

I am not getting speed information from my Airmar 2039901 transducer to my St50 plus. The reading is 0.0 kn and the transducer is clean. I have checked the connection and it is mechanically good. I have an i50 speed on the mast and I don't get any reading there either. Is there a way to test further to see if the problem is the transducer or the St50 plus? I don't mind upgrading to newer instruments but my auto pilot is a Corepak 150 and ST6001 controller and an autohelm MB 113 drive motor. I don't want to replace the auto pilot units. If I upgrade to the i50 tridata and the i60 wind do I need to replace the depth and speed transducers and the wind transducer? Thank you.

Reply to Discussion

RSS

Events

Videos

  • Add Videos
  • View All

Photos

Loading…
  • Add Photos
  • View All

Latest Activity

Robert Garrett liked Robert Garrett's profile
Sep 13
James Coolbaugh replied to Michael McDonald's discussion Integrating ST60+ instruments to eS78 Chartplotter via Seatalk Conversion Kit
"Greetings, Thia may be a bit late,but I'll try. I just installed the eS78 MFD with the Quantum (wireless) radar, which I want to use with my existing ST60 series instruments. With my old radar, they interfaced fine, but with the new…"
Sep 8
martin schulman replied to martin schulman's discussion nmea connector- C 80 chartplotter to VHF
"I can give you very little help here. After jerking around with the connection for months I finally decided to skip it. The Standard Horizon, which works beautifully despite the small screen is below and required leaving the helm to read.  I…"
Sep 4
Peter Stewart replied to martin schulman's discussion nmea connector- C 80 chartplotter to VHF
"I am purchasing a Standard Horizon gx2200 vhf with GPS and AIS. I currently have a C80 MFD. On the back of the mfd the NMEA IN/OUT connection is available. Using a RO8004 cable with the appropriate connection on one end can I join up the C80 at the…"
Sep 4
COUCHSAILORS.com updated their profile
Aug 24
COUCHSAILORS.com replied to Steve C's discussion ST60+ Tridata Not Calibrating to SOG
"When I press reset to accept the SOG which I am seeing it beeps but still shows 0.0 and doesn't transfer the SOG to the speed. Please advise."
Aug 24
Tom Arnold updated their profile
Aug 22
Donald Evans replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"All I can say is try getting your position by using the white wire! I know Ariel Cheng, she is just a temp. She doesn't know how to distinguish one wire from another. I used to deal with Evermore and found their receivers to be poor, thin wires…"
Aug 21
M.Catarall replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"You say Correct it is White wire: Rx, imput signal not data out but data in as shown on reply from Evermore"
Aug 21
Donald Evans replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"Seems you still don't understand what Cheng is saying."
Aug 21
M.Catarall replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"Evermore ( Mrs Ariel Cheng ) answered me Today: Hello Lorenzo, Red wire: VCC power (+12V) Green wire: Tx, Output signal White wire: Rx, imput signal Black wire: Ground Gray wire: Shield wire, signal ground Blue wire: Not used I did not think anyone…"
Aug 20
Donald Evans replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"You're still wrong. Evermore white wire is not the NMEA data out. And don't call me stupid. Get your facts right before commenting."
Aug 20
M.Catarall replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"The information was not wrong when posted. I suggest you look at the date of the post before adding stupid comments"
Aug 20
Donald Evans replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"Hahahahaha, you're all totally wrong. Should have bought it from www.gps-galore.co.uk The guy's an expert on these."
Aug 20
Brian Kidwell updated their profile
Aug 18
Ricky Ladd replied to Joel Hjelseth's discussion Raymarine Dragonfly 7 malfunction
"I just installed my new Dragonfly 7 pro when I power it up the Dragonfly emblem comes up it then blinks goes to a blank screen with a blinking in the upper left hand corner then it goes back to the Raymarine emblem sometimes it goes to the accept…"
Aug 8

© 2017   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service