ST5000 Plus Auotopilot using linear rudder reference on a pair of outboards.
No rudder reference is displayed while in standby mode. Shows up when in auto mode, but does not track correctly. No warnings or error message displayed. Heading is correct.
Disconnected and measured for resistance.
Red to green shows 5K
Red to blue shows 2.5K
Green to blue shows 2.7k

Reconnected all connections, still no rudder reference.
What should I try next?

Views: 1623

Reply to This

Replies to This Discussion

Unfortunately with what you have done so far, the next step is to look within the control unit at internal connections.  You will need to send the unit to the below address to be evaluated by a service technician.

Service Address:
Raymarine Service Center
9 Townsend West
Nashua, NH 03063

Include in the box:
Name
Daytime Phone
Return address
Brief description of the issue

 

Thx for info. 

Sent control unit to Raymarine Service center for testing. Confirmed issue and they reset the unit and now reads rudder again both in standby and auto.

 

One issue I have found, when rudder reference indicates midship(0) and I turn the wheel to a two(2) degree turn to the right, reference goes between full defection(2) to (30), even though outboards are just about midship. If continue the turn, the rudder reference indicates proper position. If it bounces between full deflection to many times the rudder reference blanks out.

One Ohms test I did not do was the hardover to hardover test. Will use your Rudder Reference Test.

 

Rudder Reference Test:
Red to Green: 5K Ohms (+/- 10%) Steady
Red to Blue: Variable no less than 1.5K no more than 3.5K as the wheel is spun hardover to hardover.
Blue to Green: Variable no less than 1.5K no more than 3.5K as the wheel is spun hardover to hardover.

The Red to Blue and Blue to Green may not go all the way to 1.5K or up to 3.5K, but whatever either is at midships, the deflection should be about equal to either direction(i.e. midships 2.5K if is goes up to 3.1K, it should go down to around 1.8)

Let us know what deflection values you get when you go hardover to hardover.

Did the hardover test?

Red to green = 5k Ohms
Red to blue = 2.3k-2.8k, but 2 degrees(2)right past alignment mark(0) high of 38.0k
All other readings within value.
Blue to green = 2.7k-2.5k, but 2 degrees right past alignment mark high of 160.0k
All other readings within value.

Only bad reading is 2 degrees right. Red to blue = 38.0k
Blue to green = 160.0k

Those readings seem to indicate you have a bad rudder reference unit, for the resistance to jump to that high, it appears there is an issue there.  I would recommend replacing the rudder reference sensor.

Thx for the input.
Do you know which linear feedback unit I should get?
I cannot read much on the current unit due to it being faded.
All I can see is Raytheon and the base is 17" long. I think it was installed around 1998. Red/blue/green/ground wires.
All I have is the Linear feedback unit owners handbook.
Document number:81006_2
Date: 18th August 1998

Their is no model number.
It's designed for use with outboard 'bullhorn' steering systems.

Part number for a linear rudder reference feedback sensor is M81188.

Thx for your help.
Replaced M81188 sensor and now works.

Thanks for the update.  Glad to hear you are up and running.  Happy Boating.

I recently had a similar issue with my ST5000+ used on my sailboat. The rudder bar suddenly disappeared, but all other auto pilot functions worked correctly. Resistance readings were all within the expected range, but no matter what I did, I could not get the rudder bar back. I called RM tech support, and after explaining the problem and what I had done, the technician instructed me to go into dealer setup and change the mode from sail 5000 to another mode. He then had me exit the dealer setup after which the rudder bar came back in standby mode as desired. I then re-entered dealer setup, put the system back to sail 5000, and exited. Everything is now working. I don't recall the name of the technician, but he was very helpful, and saved me the cost of pulling the unit and sending it back for "repair". I appreciate the great service.

Hello Frank,

Thank you for the kind words.  I will pass over to our autopilot phone technicians, they will appreciate the feedback.  Please contact us if there is anything we can help with in the future.

Reply to Discussion

RSS

Events

Videos

  • Add Videos
  • View All

Photos

  • Add Photos
  • View All

Latest Activity

Eric West updated their profile
Tuesday
Mark Chapman updated their profile
Jan 12
aaron sherman updated their profile
Jan 10
Craig T. Olsen updated their profile
Dec 31, 2017
David Lane replied to Tiago Menezes's discussion Night mode
"Good day and happy new year to this forum group.   Question: When can we expect Raymarine to ad a night color palette to its line of MFDs?  It’s been talked about in this forum for at least 3 years.   I am 100% satisfied with…"
Dec 31, 2017
Bob Atkins replied to Bob Atkins's discussion Current C-MAP NT+ and NT chart chips do NOT work properly on RL70C
"Hi Thomas, Please read the moderator's instructions on April 8, 2013 and my posting on October 31, 2013 on page 1 of this discussion. The issue has to do with the Plotter Mode setting. The Plotter Mode must be OFF for all…"
Dec 30, 2017
THOMAS A RICH replied to Bob Atkins's discussion Current C-MAP NT+ and NT chart chips do NOT work properly on RL70C
"Good Morning, I also have a Rl80 with the old chip and has worked perfect without any updates except last month it performed exactly as you described.  The maps I have always used now say no Data.  I was going to buy a new chip, but not…"
Dec 30, 2017
Northlightinvest replied to Ben Campbell's discussion Wheelpilot Broken Part
"Dear raymarine team! Please, give information, that where can I order this part from Hungary. 3001-984-B Thanks!"
Dec 27, 2017
Russ Colombo left a comment for lee christiansen
"Lee: Guilty as charged, now gleeful denizen of Marco Island and still sailing.  How good of you to contact, and what news??? "
Dec 14, 2017
Russ Colombo and lee christiansen are now friends
Dec 14, 2017
Russ Colombo updated their profile
Dec 13, 2017
Herve Pugin replied to cliff mesirov's discussion Mirroring via VGA to HD TV
"I have a trouble with a Gs95 HDMI output, Is the format the same: 720P ?"
Dec 11, 2017
Matthew Peacock replied to Philippe Jean Figueroa's discussion System builder and Visio icons
"Bump.  Still not resolved."
Dec 2, 2017
Bill Sincox updated their profile
Dec 1, 2017
David Jovanovic commented on Ross Smelley's blog post ECI-100 to Volvo Penta EDC1
"I hawe the same question ! Regards"
Nov 24, 2017
Sam updated their profile
Nov 20, 2017

© 2018   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service