I have a i60 Wind Indicator.  I also have a i50 speed indicator and an e125 Multifunction Display.  The speed transducer got fouled and the speed indicator read zero.  I noticed that this caused the Wind Indicator to read the same for the True and Apparent Wind.  Does the Wind indicator use the i50 speed to calculate the true wind?  It seems like it should use the COG and the SOG from the Multifunction Display (GPS).  Otherwise, the Wind Indicator would indicate true wind plus current, not the true wind.

Views: 132

Reply to This

Replies to This Discussion

True Wind calculations are produced by Speed Through the Water, not Speed Over Ground.  So it will required Speed Through the Water data, and it is the cause of True and Apparent reading the same.  Using SOG for speed, would be calculating Ground Wind Speed.

Sure would be nice to have a choice of using SOG or STW. Like I had on my old NAVman Wind that i just replaced with an I60. Hardly use STW were i am.

Reply to Discussion

RSS

Events

Videos

  • Add Videos
  • View All

Photos

  • Add Photos
  • View All

Latest Activity

Paul Grady updated their profile
May 19
Jim Capron updated their profile
May 12
Russ Lawrence replied to Tiago Menezes's discussion Night mode
"Running an a78---  I have installed V14.  Is there a version that gives us the option of a night color scheme as this time?  Or am I remembering my old Garmin system?"
May 10
Ori updated their profile
May 9
kenneth hiebert left a comment for kenneth hiebert
"After 4 years of owning Raymarine products I finally decided to join the forum. Although some of the posts are well beyond my technical understanding ,there are many layman's posts.I have also found it much easier to wire an airplane than my…"
May 8
kenneth hiebert updated their profile
May 8
EDSEL TELLIS replied to James Varner's discussion 45 series antenna with Directv
"looking for a replacement HD acu R08255 for a stv 45 antenna with a new control board R08142. is it still available and will it work."
May 2
Richard Emerson replied to Richard Emerson's discussion ST70 screen goes blank
"The light dawns. The solution was to replace the unit. At this point (2018) I'm not sure that Raymarine can still repair the unit. We were in the Exumas when the unit failed. Ultimately, I bought a replacement (successor to the ST70 - I forget…"
Apr 25
Mark Jones replied to Richard Emerson's discussion ST70 screen goes blank
"Thanks Richard, it's called Google and it searches for things on the internet.  Your problem is the same as my problem and I'd like a reply from Raymarine before they close it out because I'd like my unit to get repaired."
Apr 25
Steven Andskar updated their profile
Apr 25
Richard Emerson replied to Richard Emerson's discussion ST70 screen goes blank
"Um, I'm not sure how this popped up. The problem occurred five years ago (2013). The ticket can be closed."
Apr 24
Mark Jones replied to Richard Emerson's discussion ST70 screen goes blank
"Do we need an RMA for this?  If so, how do we get one?  My unit has been doing this for 2 years and our last calls to support didn't mention anything about this."
Apr 24
NOAM REJMAN replied to Louis Viau's discussion E80 classic radome compatibility
"hi there i have E80 & RD418D that i got from a freind swore that the system work called support yesterday asking the same question: is RD418D is compatible with E80 v5.69?  Answer was not compatible. i read on here that it is…"
Apr 17
Geoff MacDonald updated their profile
Apr 16
Germain Bélanger updated their profile
Apr 16
Colin Bondy updated their profile
Apr 8

© 2018   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service