Gentlemen:

I am planning to install speed and depth instrumentation.  The i50 Tridata unit seems to have what I'm looking for.  I have downloaded the manual, and have questions for you.
Is there a maximum displayable depth?  I have disqualified other makers' units that max out at 200 or 300 ft.
What frequencies are supported for depth transponder operation?  My Airmar B-60-20 is compatible with 200 or 50 kHz, and I would prefer to use 50 kHz to utilize the full range of the transponder's 1200 ft capability.
Is the speed function compatible with the Airmar CS4500 sensor (which I have seen listed with spade terminals for Raymarine connections)?
Thank you for your kind attention,
David Harwood

Views: 84

Reply to This

Replies to This Discussion

The i50 does not have a max depth rating, but it only utilizes the 200 kHz frequency. The i50 instrument display was never tested with the CS4500 Ultra sonic speed sensor, because it was discontinued from the Raymarine product line before the display was introduced.  I will forward to the engineers if we have any test data with the CS4500 working with the previous ST60+ instrument display line, but you might want to contact GEM Electronics Co. they are Airmar's (transducer manufacturer) North American distributor, they might be able to confirm operation.  GEM Electronics can be reached at 803.693.0777.

After a multi-year refit, my boat launched last August.  I am now attempting installation of the i50 TriData instrument in stand-alone mode (no network).

Connections: 8 discreet connections on lower back of instrument. 1-3 for depth, 4-8 for speed (& temp).  2 locking cable terminals (each with six pins) on upper back.  Can the cable terminals be used directly for depth and speed/temp connections, or are they only for network use?

I have two short cables that fit the locking terminals:  one has identical fittings on both ends and would appear to connect all six pins; the other has a different fitting on one end and connects only three pins.  Also what appears to be a blanking piece with no cable.

The speed sensor has its own connection to 12 volt source.  Will the connection to i50 terminal 8 (Red Speed V+) also power the i50, or is a separate 12v connection required (perhaps through the locking cable terminals at top, using the cable with 3-pin connection)?

Reply to Discussion

RSS

Events

Videos

  • Add Videos
  • View All

Photos

  • Add Photos
  • View All

Latest Activity

Sam updated their profile
Monday
captdanpatrick updated their profile
Sunday
Rick Fadler replied to Rick Fadler's discussion Adding Radar
"Thank you, this is really helpful!"
Sunday
Jan van der Loos replied to duco camphuijsen's discussion Ray49E error code
"Question regarding the RAY49E VHF. I'm rewiring the system. The NMEA output of the VHF, with the NMEA datasets DSC and DSE. How are they processed further in the system? It will be linked with a MFD C127.  Thanks in advance. "
Nov 13
Keith M Rodger updated their profile
Nov 7
Brad Young updated their profile
Oct 31
Jim Pra replied to Neil McCubbin's discussion Where to find full manual for a TackTick mn 100-2 wind display
"This link is no longer active.  Is the guide available somewhere else? Thanks, Jim"
Oct 30
Michael Edwards updated their profile
Oct 30
Steve Yama replied to son nguyen's discussion Part No. for Auto pilot Pump M81120 Type 1 12V
"Did you ever find your seal?  My pump is starting to leak also between the pump and motor.  Not a lot but getting to be a nuisance."
Oct 17
Brent Meyer updated their profile
Sep 21
Robert Garrett liked Robert Garrett's profile
Sep 13
James Coolbaugh replied to Michael McDonald's discussion Integrating ST60+ instruments to eS78 Chartplotter via Seatalk Conversion Kit
"Greetings, Thia may be a bit late,but I'll try. I just installed the eS78 MFD with the Quantum (wireless) radar, which I want to use with my existing ST60 series instruments. With my old radar, they interfaced fine, but with the new…"
Sep 8
martin schulman replied to martin schulman's discussion nmea connector- C 80 chartplotter to VHF
"I can give you very little help here. After jerking around with the connection for months I finally decided to skip it. The Standard Horizon, which works beautifully despite the small screen is below and required leaving the helm to read.  I…"
Sep 4
Peter Stewart replied to martin schulman's discussion nmea connector- C 80 chartplotter to VHF
"I am purchasing a Standard Horizon gx2200 vhf with GPS and AIS. I currently have a C80 MFD. On the back of the mfd the NMEA IN/OUT connection is available. Using a RO8004 cable with the appropriate connection on one end can I join up the C80 at the…"
Sep 4
COUCHSAILORS.com updated their profile
Aug 24
COUCHSAILORS.com replied to Steve C's discussion ST60+ Tridata Not Calibrating to SOG
"When I press reset to accept the SOG which I am seeing it beeps but still shows 0.0 and doesn't transfer the SOG to the speed. Please advise."
Aug 24

© 2017   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service