My I 60 display, just two months old, no longer displays any wind data.  It powers up, but the pointer remains frozen straight ahead, and the display window shows only dashed lines.

I have tried performing the self test, stages 1-4, as outlined in the downloaded installation and operations manual - but the unit will not enter the self test program as it should.

Have the procedures for running the self test been updated?  Do you have any suggestions?  Thanks - JG

Views: 1412

Reply to This

Replies to This Discussion

Hi John,

 Unfortunately, it sounds like we either have a wiring short or the i60 instrument has died. I would try the masthead wind transducer test and then if the masthead checks out, perform a factory reset. If you can't get into the dealer calibration menu or it still doesn't work after the reset, then I would pack the i60 display up and send it into the Raymarine service center.  

Attachments:

Thank you for sending the masthead test instructions.  I'm capable of doing that - I'll let you know what the test reveals.  Enjoy some NFL this weekend!  JG


My I60 shows that it is in "repeater" mode - how do I put it in "master" mode?  John

Hi John,

 The master / repeater role of the i60 wind is "auto sensed" as in if the masthead wind transducer is plugged directly into the back of the i60 then it should show master (r0), if the wind transducer is plugged into another i60 display or an iTC-5 then the display should show as a repeater(r1).


The i60 display shows r1 when I check it, though the masthead transducer is plugged directly into the back of the unit.  I have done a factory reset, or at least think I have - I changed the setting from F0 to F1,  powered down the unit then powered it back up.  Is there anything else you can suggest?  Thanks

Hi John,

 To perform a factory rest;

 After you change the setting from F0 to F1 and to exit the dealer calibration and save your changes you press and hold the Power and True / App buttons simultaneously for approximately 2 seconds.

 That being said, thus far the i60 is not seeing the masthead wind transducer. What were the masthead wind transducer readings? If they were in spec then your i60 wind display is unfortunately in need of repair. 

Masthead readings, before the failure, were in spec.  The failure did not occur suddenly, though.  For 5-6 days, we would have to power down the i60 and power it back up several times before it would show wind data.  That trick no longer works, though.

I certainly appreciate your continued assistance on this issue!  John

noted.

John

I have the same problem after 1 yr of using my i60.  What was your outcome.  Did the wind instrument fail?  Did you need to send it in for repair or did they give you a new one?  Was it covered under warranty?

I have a similar problem. The wind needle sometimes registers erratically and incorrectly but mostly is frozen in the 12 oclock position even though the vane is turned in a different direction and moving. The wind speed used to register erratically too but now just shows dashes. How can I determine what problem is?

ST60+ Similar problem

On yesterday's sail, our ST60+ wind instrument stopped showing either direction or speed, reverting to--- on display.  When powered up and then powered down, it showed speed and direction again briefly and then reverted to 0.0, then ---.  We performed suggested voltage tests at the instrument and found the following readings  - red 7.9v, blue 5.2v, green 6.7v, yellow 3.3v.   We powered up and down again, by removing and reattaching the seatalk connector which supplies power to the instrument.  We then got readings again, which lasted for almost ten minutes before reverting to 0.0 and ---.  Every now and then, at this point, the direction arrow will twitch, and the speed may show momentarily, but again reverts to 0.0 and ---.  The voltage was consistently just a little less than 8vdc, rather then 8+.  Could this be the problem?  Not sure why, tho, as tridata, powered by ST from the wind meter, is working fine.

I have made following measurements. Can someone advise if problem is ST60 Display unit , xducer or both?
Xducer cable only:
R-Shield. 21.6 k ohms
G-Shield. 38.6 k ohms
B-Shield. 6.1 ohms
Y-Shield. 65.4 k ohms

Instrument only powered by network
R-Shield. 8v DC
G-Shield. 0.001 v DC
B-Shield. 0.001 v DC
Y-Shield. 8.0 v DC

Instrument powered with xducer connected:
R-Shield. 8 v DC
G-Shield. 5.6 v DC
B-Shield. -0.03 v DC
Y-Shield. 3.6 v AC. Not DC

Reply to Discussion

RSS

Events

Videos

  • Add Videos
  • View All

Photos

  • Add Photos
  • View All

Latest Activity

Eric West updated their profile
Tuesday
Mark Chapman updated their profile
Jan 12
aaron sherman updated their profile
Jan 10
Craig T. Olsen updated their profile
Dec 31, 2017
David Lane replied to Tiago Menezes's discussion Night mode
"Good day and happy new year to this forum group.   Question: When can we expect Raymarine to ad a night color palette to its line of MFDs?  It’s been talked about in this forum for at least 3 years.   I am 100% satisfied with…"
Dec 31, 2017
Bob Atkins replied to Bob Atkins's discussion Current C-MAP NT+ and NT chart chips do NOT work properly on RL70C
"Hi Thomas, Please read the moderator's instructions on April 8, 2013 and my posting on October 31, 2013 on page 1 of this discussion. The issue has to do with the Plotter Mode setting. The Plotter Mode must be OFF for all…"
Dec 30, 2017
THOMAS A RICH replied to Bob Atkins's discussion Current C-MAP NT+ and NT chart chips do NOT work properly on RL70C
"Good Morning, I also have a Rl80 with the old chip and has worked perfect without any updates except last month it performed exactly as you described.  The maps I have always used now say no Data.  I was going to buy a new chip, but not…"
Dec 30, 2017
Northlightinvest replied to Ben Campbell's discussion Wheelpilot Broken Part
"Dear raymarine team! Please, give information, that where can I order this part from Hungary. 3001-984-B Thanks!"
Dec 27, 2017
Russ Colombo left a comment for lee christiansen
"Lee: Guilty as charged, now gleeful denizen of Marco Island and still sailing.  How good of you to contact, and what news??? "
Dec 14, 2017
Russ Colombo and lee christiansen are now friends
Dec 14, 2017
Russ Colombo updated their profile
Dec 13, 2017
Herve Pugin replied to cliff mesirov's discussion Mirroring via VGA to HD TV
"I have a trouble with a Gs95 HDMI output, Is the format the same: 720P ?"
Dec 11, 2017
Matthew Peacock replied to Philippe Jean Figueroa's discussion System builder and Visio icons
"Bump.  Still not resolved."
Dec 2, 2017
Bill Sincox updated their profile
Dec 1, 2017
David Jovanovic commented on Ross Smelley's blog post ECI-100 to Volvo Penta EDC1
"I hawe the same question ! Regards"
Nov 24, 2017
Sam updated their profile
Nov 20, 2017

© 2018   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service