Connecting on mast i50s as repeaters to a below deck (in the salon) corepak 150 course computer

I am mounting 2 i50s on the mast as repeaters for an st50 plus and st6001 network. I think I can connect the 2 i50s with a spur cable and then take a spur cable through the deck and to t an r52131 converter and from there to the corepak 150 course computer. I also have an Interface E85001 hooked to the corepak 150 that I used to use for a B&G display which I no longer have. Is this the correct and simplest way to connect i50s to my network? Is there a through deck fitting from Raymarine that fits the cable properly and then do I need more cables? Simplest of all would be to take a spur cable from the mast and connect directly to the course computer. Does this also work? Thx, JD 

Views: 55

Reply to This

Replies to This Discussion

With these products, the converter (E22158) will be the best and simplest way to connect them together.  Raymarine does not have any fittings for cable runs.  To confirm, you would daisy chain the i50's then run them to the Seatalk to Seatalk NG converter, into the while port, the ST50+ and ST6001 Seatalk equipment will be connected to the converter through the Seatalk yellow port.  The last existing white port will be connected to power, to energize the Seatalk NG interface.

No, the Type 150 CC does not have a Seatalk NG interface available, so a direct connection is not suggested.

Reply to Discussion

RSS

Events

Videos

  • Add Videos
  • View All

Photos

  • Add Photos
  • View All

Latest Activity

Jan van der Loos replied to duco camphuijsen's discussion Ray49E error code
"Question regarding the RAY49E VHF. I'm rewiring the system. The NMEA output of the VHF, with the NMEA datasets DSC and DSE. How are they processed further in the system? It will be linked with a MFD C127.  Thanks in advance. "
Monday
Keith M Rodger updated their profile
Nov 7
Brad Young updated their profile
Oct 31
Jim Pra replied to Neil McCubbin's discussion Where to find full manual for a TackTick mn 100-2 wind display
"This link is no longer active.  Is the guide available somewhere else? Thanks, Jim"
Oct 30
Michael Edwards updated their profile
Oct 30
Steve Yama replied to son nguyen's discussion Part No. for Auto pilot Pump M81120 Type 1 12V
"Did you ever find your seal?  My pump is starting to leak also between the pump and motor.  Not a lot but getting to be a nuisance."
Oct 17
Brent Meyer updated their profile
Sep 21
Robert Garrett liked Robert Garrett's profile
Sep 13
James Coolbaugh replied to Michael McDonald's discussion Integrating ST60+ instruments to eS78 Chartplotter via Seatalk Conversion Kit
"Greetings, Thia may be a bit late,but I'll try. I just installed the eS78 MFD with the Quantum (wireless) radar, which I want to use with my existing ST60 series instruments. With my old radar, they interfaced fine, but with the new…"
Sep 8
martin schulman replied to martin schulman's discussion nmea connector- C 80 chartplotter to VHF
"I can give you very little help here. After jerking around with the connection for months I finally decided to skip it. The Standard Horizon, which works beautifully despite the small screen is below and required leaving the helm to read.  I…"
Sep 4
Peter Stewart replied to martin schulman's discussion nmea connector- C 80 chartplotter to VHF
"I am purchasing a Standard Horizon gx2200 vhf with GPS and AIS. I currently have a C80 MFD. On the back of the mfd the NMEA IN/OUT connection is available. Using a RO8004 cable with the appropriate connection on one end can I join up the C80 at the…"
Sep 4
COUCHSAILORS.com updated their profile
Aug 24
COUCHSAILORS.com replied to Steve C's discussion ST60+ Tridata Not Calibrating to SOG
"When I press reset to accept the SOG which I am seeing it beeps but still shows 0.0 and doesn't transfer the SOG to the speed. Please advise."
Aug 24
Tom Arnold updated their profile
Aug 22
Donald Evans replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"All I can say is try getting your position by using the white wire! I know Ariel Cheng, she is just a temp. She doesn't know how to distinguish one wire from another. I used to deal with Evermore and found their receivers to be poor, thin wires…"
Aug 21
M.Catarall replied to Lorenzo Vanni's discussion Raychart BC420 and Evermore SA-320
"You say Correct it is White wire: Rx, imput signal not data out but data in as shown on reply from Evermore"
Aug 21

© 2017   Created by Moderator - Raymarine, US.   Powered by

Badges  |  Report an Issue  |  Terms of Service